Bow and skew in fabric are distortions of the weft (filling) yarns. In a perfect woven fabric, the weft runs straight across the width at 90° to the selvages. Bow means the weft curves into an arc. Skew means it runs straight but at an angle, so one edge leads the other.
Most guides discuss bow and skew in apparel fabric. This article looks at them from the coated-fabric side, using a real order. An established raw-material distributor in Russia, which supplies fabric to manufacturers, visited our factory and then ordered nine PVC-coated fabric specifications: four for awnings and five for inflatable boats. Their specification sheet set one limit that apparel buyers rarely write: weft skew of no more than 2 cm on the boat fabric.
For the base-fabric side of this topic, see our guide to PVC coated polyester fabric.
I. What Are Bow and Skew in Fabric?
Both defects describe how far the weft yarns move away from a straight line across the fabric width.
| Defect | What the weft does | What you see |
|---|---|---|
| Bow | Curves into an arc; the middle runs ahead of or behind the edges | A “smile” or “frown” across the width |
| Skew | Stays straight but runs at an angle | One selvage leads the other |
How Bow and Skew Are Measured
The fabric is laid flat without tension. A straight line is drawn from selvage to selvage, and the distance between that line and the actual weft is measured. ASTM D3882 is a common test method for this.
The result can be written in two ways:
- As a distance, for example 2 cm.
- As a percentage of the width: distortion (%) = offset ÷ width × 100.
For the boat fabric in this order, the width was 2.18 m. A 2 cm limit on that width is about 0.9%.
II. Why Skew Matters More in Coated Fabric for Inflatables
In apparel, bow and skew mostly cause pattern misalignment and twisted seams. In coated fabric for inflatable boats, they also affect how the product is built.
Our view, from producing inflatable fabric:
- Panels are cut to a grain line. Boat tubes are made from many cut panels. If the weft is skewed, the yarns no longer run square to the panel edges.
- Seams are welded, not sewn. Welded seams join panels edge to edge. Panels whose yarns run off-square are harder to match along long seams.
- The tube is under pressure. An inflated tube puts the fabric under load. A panel with off-square yarns does not take that load the same way as a straight one.
In this order, the 2 cm skew limit applied to the boat fabric.
III. Where Bow and Skew Come From
Bow and skew can start in weaving, when weft tension is uneven, and in finishing, when the fabric runs through rollers and dryers under uneven tension.
In PVC-coated fabric, two more stages matter:
- The base fabric. Our base fabrics are woven from high-strength polyester industrial yarn. A straight, stable base fabric is the starting point for a straight coated fabric.
- The coating or lamination line. The fabric is pulled through the line under tension and heat. Even tension across the width keeps the weft straight.
Weft skew is part of our routine inspection, together with peel strength, tear and tensile strength, weight, thickness and color difference.
IV. The Project: Nine Specifications for a Distributor in Russia
The customer is an established importer and distributor of raw materials for manufacturers, with about 30 years in the business and more than 100 stores, selling both wholesale and retail. They were looking to replace an existing supplier in China. After visiting our factory, they chose us on service, price and product quality, and ordered all nine specifications.
Awning Fabric
| GSM | Base fabric | Density | Thickness (approx.) | Surface | Width |
|---|---|---|---|---|---|
| 600 | 1000D × 1000D | 20 × 20 | 0.5 mm | Glossy | 2.5 m |
| 450 | 500D × 500D | 18 × 18 | 0.35 mm | Glossy | 2.5 m |
| 350 | 250D × 250D | 18 × 18 | 0.3 mm | Matt | 2.5 m |
| 475 | 1000D × 1000D | 18 × 18 | 0.37 mm | Matt | 1.55 m |
Inflatable Boat Fabric
| GSM | Base fabric | Density | Thickness (approx.) | Surface | Width |
|---|---|---|---|---|---|
| 550 | 1000D × 1000D | 18 × 18 | 0.45 mm | Matt | 2.18 m |
| 600 | 1000D × 1000D | 20 × 22 | 0.5 mm | Matt | 2.18 m |
| 700 | 1000D × 1000D | 23 × 23 | 0.6 mm | Matt | 2.18 m |
| 800 | 1000D × 1000D | 23 × 23 | 0.7 mm | Matt | 2.18 m |
| 1050 | 1000D × 1000D | 28 × 26 | 0.82 mm | Matt | 2.18 m |
Two requirements applied across the order:
- Weft skew of no more than 2 cm on the boat fabric.
- A service temperature of −30 °C to +70 °C, which our material meets in testing.
What the Specification Sheet Shows
The boat fabric uses the same 1000D base yarn across all five weights. The weight steps up with the thread density, from 18 × 18 to 28 × 26. In our experience, the base fabric decides most of the tensile and tear strength, and the coating process has a smaller effect. Raising the density of the same yarn is a direct way to build a stronger, heavier boat fabric.
V. Our View: How to Write Bow and Skew Into a Coated Fabric Spec
From this order and others, here is what we suggest buyers put in writing:
- State the limit and the width. “Weft skew ≤ 2 cm” is clear when the roll width is fixed. If the width may change, also give the limit as a percentage.
- Say which products it applies to. A tight skew limit matters most for fabric that will be cut into panels and welded, such as inflatable boat fabric.
- Agree the measuring method. Name the test method, or describe how the roll is laid out and measured, so both sides get the same number.
- Choose the construction by end use first. For inflatable boats, ask for an airtight construction. We do not recommend knife-coated fabric for inflatables, because knife coating can leave micro-pores; laminated or impregnated constructions hold air better.
VI. FAQ
What is a bowing defect in fabric?
A bowing defect is when the weft yarns curve into an arc across the width of the fabric instead of running straight. The middle of the weft runs ahead of or behind the edges.
How to calculate bowing in fabric?
Lay the fabric flat without tension, measure the largest distance between a straight line across the width and the bowed weft, divide it by the fabric width and multiply by 100. The result is the bow as a percentage.
What is warp and weft in textiles?
The warp yarns run along the length of the fabric. The weft (or filling) yarns run across the width, at right angles to the warp. Bow and skew are distortions of the weft.