2.3 PVC Resin

PVC resin is the base polymer of the PVC coating. Every other ingredient is measured against it: coating formulas are written in PHR, or parts per hundred parts of resin, so a plasticizer level of 70 PHR means 70 kg of plasticizer for every 100 kg of PVC resin. The grade of resin sets the ceiling for the coating’s strength, low-temperature behavior and aging resistance; the rest of the formula and the process decide how much of that potential the finished fabric reaches.

2.3.1 Suspension Resin vs. Paste Resin

PVC coated fabric production uses two physical forms of resin, and each one belongs to a different production route.

Comparison Suspension (Powder) Resin Paste (Emulsion) Resin
Physical Form Free-flowing powder with relatively coarse particles Very fine particles that disperse in plasticizer
How It Is Processed Dry-blended with plasticizer and additives, then plasticized and rolled into film on a calender Stirred into plasticizer and additives to form a liquid paste (plastisol)
Production Route Calendered PVC film for cold lamination, hot lamination and pre-coated film lamination Knife coating, impregnation and the bonding layer of pre-coated film
Typical Grades Chinese SG-3 and SG-5 grades are common in tarpaulin film Selected by paste viscosity and fusion behavior

This is the material-level reason behind the two product families: film-based PVC laminated fabric is built on suspension resin, while knife-coated PVC coated fabric is built on paste resin. LonaTarp calenders its own film and mixes its own paste, so both resin types are selected in-house for each formula.

2.3.2 Molecular Weight, Degree of Polymerization and K-Value

Resin grades are compared by how long the polymer chains are. Three related terms describe this:

Term What It Means How It Is Used
Molecular Weight The actual mass of a PVC polymer chain. A higher molecular weight means a longer chain The underlying property; rarely quoted directly in trade
Degree of Polymerization (DP) The number of vinyl chloride units (CH₂=CHCl) linked in one chain. Each unit weighs 62.5 g/mol, so number-average molecular weight = DP × 62.5 A DP of 1,000 gives a molecular weight of 62,500 g/mol
K-Value An indirect measure of molecular weight, calculated from the viscosity of a PVC solution. A higher K-value means a higher molecular weight The most common way resin grades are compared in industry
Resin Grade A commercial grade defined by a K-value or molecular weight range. In the Chinese standard, general-purpose suspension grades start with “SG” SG-5 is the most common grade, widely used for pipes and profiles. Tarpaulin production commonly uses SG-5 and SG-3
S-60, S-65, S-70, S-80 Grade names used in everyday trade to indicate different degrees of polymerization Common shorthand between resin suppliers and coaters

Generally, a higher K-value or degree of polymerization raises the performance potential of the coating:

Higher K-Value / DP Effect
Mechanical Properties Higher tensile strength, impact strength and modulus
Durability Better heat resistance, low-temperature performance and aging resistance
Processing Lower melt flow, so the compound is harder to process
Cost Usually higher

Higher is not automatically better for every order. A higher-K resin makes sense for products that face cold climates, repeated flexing or long outdoor service; a general-purpose grade keeps cost and processing under control for standard covers. Actual performance always depends on the full formula and process, not on the resin grade alone.

2.3.3 Ethylene Route vs. Calcium Carbide Route

Vinyl chloride monomer, the building block of PVC resin, is made by two industrial routes. The route affects the molecular weight distribution of the resin and, through it, thermal stability and processing.

Comparison Ethylene Route Calcium Carbide Route
Feedstock Petroleum and natural gas Coal, limestone and salt
Process Petroleum is cracked to ethylene; ethylene reacts with chlorine to form ethylene dichloride, which is cracked at high temperature into vinyl chloride monomer (VCM) Coke and limestone react in an electric furnace to form calcium carbide; carbide reacts with water to form acetylene, which reacts with hydrogen chloride over a mercury-salt catalyst to form VCM
Resin Characteristics Higher molecular weight with a narrower distribution; better thermal stability and mechanical properties Lower molecular weight with a broader distribution; slightly lower thermal stability but plasticizes easily
Share of China’s Capacity About 28% About 72%; the mainstream route
Main Production Regions Coastal East and South China Coal-rich central and western regions such as Inner Mongolia, Xinjiang and Ningxia
Typical Use Applications that need consistent long-term performance General-purpose applications

The calcium carbide route suits China’s resource base of abundant coal and limited oil and gas. It is the lower-cost route, but it carries a higher pollution burden, and its resin meets general-purpose requirements. LonaTarp mainly uses ethylene-route resin for its PVC coated fabrics.

You do not need to specify the resin grade or production route in an inquiry. Tell us the end use, service temperature and expected outdoor life, and we select the resin together with the plasticizer, stabilizer and additives to meet them. For a quotation, contact our team.