3. Manufacturing Processes

3.1 Lamination

Lamination is the process of bonding PVC film to the base fabric, and it is how PVC laminated fabric is made. In the narrow sense, lamination covers cold lamination and hot lamination, which differ in the temperature and sequence used to bond the film to the fabric. In the broad sense, it also includes pre-coated film lamination and impregnation (wet paste).

Process How the PVC Is Bonded Scope
Cold Lamination Heated PVC film is laminated directly to the base fabric Lamination in the narrow sense
Hot Lamination One PVC film is bonded to the base fabric first, then laminated to a second film Lamination in the narrow sense
Pre-Coated Film Lamination A thin layer of PVC paste on the film strengthens the bond to the base fabric Lamination in the broad sense; see 3.2
Impregnation (Wet Paste) The base fabric is soaked in PVC paste and fused before lamination Lamination in the broad sense; see 3.3

LonaTarp calenders its own PVC film and runs all four processes in-house, so the lamination route can be chosen to suit the base fabric and the end use.

3.1.1 Cold Lamination vs. Hot Lamination

Process How It Works Advantages Limitations
Cold Lamination PVC film is heated and then laminated to the base fabric Fast; better thickness at the same weight; tensile and tear strength can be good The bond between the face and back layers may be weaker, with a higher risk of peeling
Hot Lamination One film is bonded to the base fabric first, then laminated to the other film Higher bond strength between the face and back PVC layers Heat on the base fabric may affect its strength, so tensile and tear strength may drop

The trade-off is between mechanical strength and bond strength. Cold lamination protects the strength of the base fabric; hot lamination builds a stronger bond between the two PVC layers. For products that are folded, flexed or welded often, bond strength usually carries more weight.

3.1.2 Base Fabric Density and Peel Strength

In laminated vinyl fabric, the peel strength is inversely proportional to the density of the base fabric. The face and back PVC layers hold together largely by bonding to each other through the openings between the yarns. A dense fabric leaves fewer and smaller openings, so there is less contact between the two layers and the peel strength drops. That is why dense base fabrics, or orders that need high peel strength, call for pre-coated film lamination or impregnation rather than plain cold or hot lamination.

Peel strength is the bond between the coating and the fabric, and it is measured by standard methods such as ISO 2411, the international method for determining the coating adhesion of coated fabrics. Every production run of LonaTarp PVC fabric is tested for peel strength.

3.1.3 Why Vinyl Fabric Delaminates

“Will your fabric delaminate?” is one of the most common questions from buyers. Delamination, or peeling, is usually a sign of insufficient peel strength, and it can come from several sources:

Possible Cause What Happens
Base Fabric Too Dense The face and back PVC layers have too little contact through the fabric openings
Insufficient Pre-Coat or Impregnation Not enough paste to anchor the film to the yarns
Lamination Temperature and Pressure Poor control leaves a weak bond from the start
Paste Cross-Linking Incomplete fusion of the paste weakens the bond
Long-Term Aging The bond weakens as the material ages
Repeated Folding Flexing concentrates stress at the interface between PVC and fabric
Welding or Service Beyond the Design Range Heat, load or conditions exceed what the construction was built for

We prevent this at the design stage: by matching the base fabric density to the lamination route, using pre-coating or impregnation where the fabric is dense, controlling lamination temperature and pressure, and checking peel strength on every run. When you tell us how the product will be used, including folding, welding and service conditions, we select the construction to suit. Lamination is one of the two main production routes; the other is knife coating, and the differences between them are set out in knife coating vs. lamination.

Send us your application, and we will recommend the lamination route and confirm it on a trial sample before bulk production.