1680D PVC Polyester Fabric Rolls
1680D PVC polyester fabric is a heavy-duty polyester base woven from 1680-denier yarn and coated with PVC on both sides, by knife coating or lamination. The thick yarn gives high tear and abrasion resistance, so fabricators use it where covers, curtains and cases take hard daily wear.
We supply it in rolls up to 3.2 m wide, with density, coating route and surface set to the product you make and confirmed on a sample before production.
What Does 1680D Mean in PVC Fabric?
1680D means the polyester yarn weighs 1,680 grams per 9,000 meters. It describes how thick the yarn in the base fabric is, not the weight of the finished fabric. The final weight depends on the weave density and the amount of PVC on each side, so it is fixed on the approved sample.
Is 1680D Polyester Strong?
Yes. 1680D is one of the thicker yarns used in PVC coated fabric. Compared with a 1000D base, it gives more tear resistance, abrasion resistance and load capacity at the same density. The trade-off is weight and stiffness: 1680D fabric is heavier and less pliable, so it suits hard-wearing products more than covers that are folded by hand many times a day.
| Base Yarn |
Character |
Better Suited To |
| 1000D |
Strong, lighter and easier to fold |
General truck tarps and covers |
| 1680D |
Higher tear and abrasion resistance, heavier and stiffer |
Heavy-wear covers, curtains and cases |
| 2000D |
Heaviest handling of the three |
The most demanding load and wear conditions |
Yarn size is only part of the strength. Density and coating decide the final figures, which are tested for your build. For other bases, see our
1000 denier PVC coated polyester and
2000 denier PVC fabric.
Knife-Coated or Laminated 1680D PVC Fabric
We make 1680D PVC fabric in two constructions, both with PVC on both faces:
| Construction |
How the PVC Is Applied |
| Knife-coated |
PVC paste is spread onto the base fabric with a blade, then fused with heat |
| Laminated |
PVC film is bonded to both sides of the base fabric under heat and pressure |
We recommend the construction after reviewing your product, welding method and surface finish, and confirm it on a sample. For a full comparison, read
knife coating vs lamination.
Functions of 1680D PVC Fabric
- Waterproof: PVC on both faces forms a continuous barrier
- High tear and abrasion resistance from the 1680D base
- Flame retardant options, with NFPA 701 and DIN 4102 test reports
- UV resistant and anti-mildew treatments for outdoor use
- Cold resistant to -30°C
- Glossy, matte or embossed surfaces, with acrylic or PVDF top coats available
- DOTP non-phthalate or Ca/Zn lead-free formulations, with test reports
- Weldable with high-frequency, hot-air and hot-wedge equipment
What Fabricators Make with 1680D PVC Fabric
- Heavy-duty truck covers and dump truck tarps
- Truck side curtains in high-use fleets
- Heavy machinery and equipment covers
- Industrial tool bags and protective cases
- Wear pads and reinforcement patches for high-abrasion areas
- Heavy ground protection sheets
Ordering 1680D PVC Fabric
| Item |
What We Agree With You |
| Base Fabric |
1680D polyester |
| Construction |
Knife-coated or laminated, PVC on both sides |
| Density |
Custom, set to the strength and handling your product needs |
| Weight |
Set by density and coating; fixed on the approved sample |
| Width |
Up to 3.2 m |
| Color and Surface |
Custom colors; glossy, matte or embossed |
| Testing |
Weight, width, coating adhesion, tensile and tear strength, and color difference tested on every run |
| MOQ and Lead Time |
5,000 m² per order; usually about 15 days after the specification is confirmed |
To get a quote, send us the product you make, knife-coated or laminated construction if you have a preference, roll width and length, color and surface, options such as flame retardant or UV, and quantity and destination port. You can also compare other grades in our
PVC coated fabric range.
FAQ
Is 1680D PVC fabric waterproof?
Yes. Both faces are coated with PVC, which forms a continuous barrier. In finished products, seams and stitch holes also need welding or sealing to keep water out.
1680D or 1000D: which do you need?
Choose 1680D when the product takes heavy abrasion, dragging or loads, and the extra weight is acceptable. Choose 1000D when the fabric must stay lighter and easier to fold and handle.